Linear Gate Parts & Welding Nationwide

Linear Gate Parts & Welding in Tarzana: What to Know First

We provide independent Linear gate parts and welding across Tarzana, with most hinge, post, rail, and roller repairs completed in a single visit. A worn hinge or a cracked weld on a Linear swing gate typically runs $180 to $450 depending on what’s actually failed, and we quote the full price before any work starts. This page is for Tarzana homeowners with a Linear gate that’s sagging, scraping, or refusing to close square. If that’s your gate, call (925) 263-6107 and a live person will answer, day or night.

Call (925) 263-6107

Key Takeaways

• We’re an independent Linear service provider, not a factory shop, and we carry or source OEM and quality aftermarket parts for most Linear swing and slide gate models in the Tarzana area.
• Hinge replacement, post resetting, rail repair, gate rollers, and custom welding on Linear gates are jobs we do week in and week out across Tarzana, Encino, Woodland Hills, and Reseda.
• Upfront pricing, settled before a single bolt gets turned. Most Linear parts and welding jobs are done in one visit and every job carries our 90-Day Done Right Promise in writing.

How Linear Products Fail - and How We Fix Them

Linear gates are common across Tarzana, especially on homes built from the late 1980s through the early 2000s. Over 42 years of working on them, we’ve learned exactly where they break. Here’s what we see:

• Worn hinge brackets on Linear swing gate arms, especially the LRA and HAE series. The factory hinge bracket is stamped steel, and after years of Tarzana sun and daily cycles, the metal fatigues at the weld point. The gate sags, the actuator strains, and eventually the bracket tears. We cut out the old bracket, weld in a heavy-gauge replacement, and reinforce the post mount so it doesn’t happen again.
• Post rot and cracking at the hinge line on Linear dual-swing installations. Tarzana’s hot, dry summers shrink the soil, and winter rains swell it back. Gate posts on Linear dual-swing systems take that movement year after year. The post shifts, the gate drops, and the opener fights the geometry every cycle. We reset posts in new concrete with proper depth, or weld a new steel post sleeve when the original is too far gone.
• Rail wear on Linear slide gate models like the SL and G series. The slide rail on these gates is exposed to dust, grit, and dry leaves eight months of the year in Tarzana. The rollers pick up debris, the rail grooves wear uneven, and the gate starts to bind. We straighten or replace the rail, replace the rollers, and set the track so the gate rolls without the opener working double duty.
• Cracked welds where the gate frame meets the operator mounting plate on Linear swing arm actuators. This is a Linear-specific pattern we’ve seen dozens of times in Tarzana. The actuator plate gets welded to a thin-wall tube, and constant cycling stress cracks the tube right at the heat-affected zone of the original weld. We cut the cracked section back to solid metal and weld in a reinforcing plate before remounting the operator.
• Worn latch receivers and lock brackets on Linear gates with older magnetic or solenoid locks. The receiver plate works loose, the latch misses, and the opener keeps pushing against a gate that hasn’t fully closed. We weld in a new receiver plate, set the latch throw, and adjust the close limit on the Linear control board so the gate actually closes and locks the first time.

Each of these fixes addresses the part that failed. But more importantly, we address why it failed. That’s the difference between a patch job and a repair that stays repaired.

Our Linear Gate Parts & Welding Process

When a Tarzana homeowner calls about a Linear gate that isn’t closing right, here’s how we handle it from start to finish:

1. 1
   The call. You talk to a person, not a recording, 24 hours a day. We ask what the gate is doing, what it sounds like, and when it started.
2. 2
   The visit. A uniformed, background-checked technician arrives at the time we agreed on. We inspect the gate, the hinges, the posts, the rail, the rollers, and the Linear operator as one system, not a list of separate parts.
3. 3
   The parts decision. We tell you straight whether your Linear gate needs an OEM part, a quality aftermarket equivalent, or a custom-fabricated piece welded in place. You’ll know what it costs before we pick up a tool.
4. 4
   The work. Hinges cut out and welded, posts reset or sleeved, rails straightened, rollers replaced. We work clean and we clean up after ourselves. If your driveway is your mother’s driveway, we treat it exactly that way.
5. 5
   The test. We cycle the gate open and closed repeatedly, adjust the limits on the Linear control board, and make sure the gate seals square against the stops. Then we watch it cycle again with the safety edges and photo eyes in play.
6. 6
   The guarantee. Every Linear parts and welding job we complete is covered by our 90-Day Done Right Promise, in writing. If it’s not right, we come back and make it right. No paperwork, no arguing.

What Linear Gate Parts & Welding Costs in Tarzana

Here are honest numbers for the Linear gate repairs we most often handle in Tarzana:

• Hinge replacement, single swing gate: $180 to $320
• Hinge replacement, dual-swing Linear gate with actuator arm: $350 to $550
• Post reset in concrete, single post: $280 to $475
• Rail repair or replacement, slide gate: $300 to $700 depending on rail length and condition
• Custom welding, cracked frame or failed mounting plate: $200 to $450
• Gate roller replacement, set of rollers: $90 to $180
• Latch and lock receiver re-weld and adjustment: $120 to $240

What moves the price: how far the post has shifted, whether the gate frame has cracked metal or just worn parts, and whether we’re repairing existing structure or building new. Every price gets quoted and agreed before work starts, so the invoice never surprises you. Call (925) 263-6107 for a free estimate on your Linear gate, and remember we always offer a free second opinion on any written estimate you’ve received from another company.

Why Tarzana Homeowners Call Ironworks Gate Co. for Linear Work

We’ve been doing this work in the Valley for over 42 years, and we plan to be doing it for another 40. That changes how we approach a Linear gate repair. We don’t patch a hinge and hope for the best because we know we’ll drive past your house next month. Victor Salinas grew up off Reseda Boulevard in Tarzana and learned metalwork and electrical systems at Los Angeles Pierce College, where a shop instructor told him something that’s stuck with him since: a gate is only as honest as the person who built it. That’s the standard we work to.

We service Linear every week, but we also carry service expertise on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. When a Linear gate has a problem that turns out to be a control board issue rather than a weld issue, we fix that too, because we’re trained across nine major gate automation brands. A live person answers our phone around the clock. We show up when we say we will. And every job carries our 90-Day Done Right Promise in writing.

A gate should open when you want it to and stay closed when you don’t. Everything else is just keeping that promise.

FAQs