Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Tarzana: What to Know First
FAAC gate installation in Tarzana typically runs between $2,800 and $7,400 for a complete single-driveway system, parts and labor included. Most FAAC installs we handle are completed within one to two working days, and we quote every job upfront before a single bolt is turned. As an independent FAAC service provider, we carry the hydraulic and electromechanical lines that fit Tarzana driveways best, and we install them properly the first time.
If you own a FAAC unit that needs mounting, a full system replacement, or a gate built to carry one, you’re in the right place. Call (925) 263-6107 and Victor or one of our techs will talk you through what you have and what it’ll take.
How FAAC Products Fail - and How We Fix Them
- FAAC 400 Series hydraulic operators - slow drift on hot afternoons. Tarzana summers push 100°F and hydraulic fluid thins. We see 400-series units that work fine at 8 a.m. and crawl by 3 p.m. The fix is usually a fluid replacement and seal kit, not a new pump. We test at temperature, not in the shade, because that’s when your gate actually needs to open.
- FAAC 750 and 760 sliding gate models - limit switch drift. These units use magnetic limit switches that can wander over time, leaving the gate stopping short or over-traveling into the end stop. A homeowner with a multimeter and a prayer usually makes it worse. We re-set limits and confirm the brake engages at the right point so the gate doesn’t slam or stall.
- FAAC E145/S800H barrier arms - control board failures after power flickers. Southern California Edison voltage dips are hard on control boards. The E145 is a workhorse, but after enough brownouts the board forgets its programming. We install surge protection on every FAAC job as standard practice, which the manufacturer doesn’t always spec but Tarzana electrical reality demands.
- FAAC swing gate hinges - the forgotten half of the job. A gate installation isn’t just the operator. We routinely see FAAC motors bolted to gates hanging on hinges worn ten degrees out of square. The motor burns out trying to move a gate the hinge won’t let move. On every FAAC install, we weld and align the hinge posts first, then mount the operator. Skipping that step is why some FAAC units die in five years instead of twenty.
- FAAC photocell and safety-edge wiring - corroded connections near sprinkler overspray. Tarzana yards are irrigated heavily, and low-voltage safety wiring near gate posts takes constant moisture. We use sealed connectors and elevate control boxes above grade. A FAAC install that ignores moisture is a gate that stops mid-cycle and leaves the driveway half open. We don’t do that.
Our FAAC Gate Installation Process
Here’s how a FAAC gate installation actually goes when you call Ironworks Gate Co.
- 1
Call and talk to a person. A live person answers 24/7. Tell us what brand and model you have, what the gate is doing or not doing, and we’ll give you a straight read on what’s likely involved.
- 2
Free on-site assessment. We come to your Tarzana property, measure the gate, check the hinges, power availability, and site conditions. We don’t quote over the phone because a gate that looks straightforward in a photo often isn’t.
- 3
Written quote, agreed before work begins. We give you the price upfront, in writing. No surprises on the bill. If we find something unexpected, we stop and call you first. The price we agree on is the price you pay.
- 4
Installation day. We mount, wire, program, and test. For FAAC hydraulic units, we bleed the system properly. For electromechanical, we set limits, torque, and safety edges. We run full open and close cycles, test obstruction response, and confirm the emergency release works.
- 5
Walkthrough. We show you how to operate the manual release, how to reset a fault, and what normal operation looks and sounds like. If you have a remote or keypad, we program it with you standing there.
- 6
Cleanup and guarantee. We leave the job site cleaner than we found it, and every FAAC installation carries our 90-Day Done Right Promise in writing. If it’s not right, we come back and make it right. No arguing, no forms, no exceptions.
What FAAC Gate Installation Costs in Tarzana
Here are honest price ranges for common FAAC installation scenarios in Tarzana. These include labor, mounting hardware, and basic electrical connection. Parts are line-itemed, so you can see exactly where your money goes.
- FAAC 400 hydraulic swing operator, single gate: $2,800-$4,200 installed
- FAAC 750 sliding gate operator, single driveway: $3,100-$4,900 installed
- FAAC 760 sliding operator with battery backup: $3,600-$5,400 installed
- Dual swing gate system with two FAAC 400 operators: $5,200-$7,400 installed
- FAAC operator replacement (existing gate, reuse hinges and posts): $1,500-$2,600 installed
- Photocell pair, keypad, or safety edge addition: $250-$600 per component, installed
What moves the price: gate weight and length, hinge condition, distance from the panel to the operator, whether you need a new control board or battery, and whether we’re welding new posts. Everything is quoted and agreed before work starts. Call (925) 263-6107 for a free estimate on your specific FAAC setup.
Why Tarzana Homeowners Call Ironworks Gate Co. for FAAC Work
We’ve been serving the West Valley for over 42 years, founded in 1984, and we plan to be here for another forty. Victor Salinas grew up off Reseda Boulevard, not far from the old Braemar Country Club, and he’s still here. When you call, you get a live person. When we schedule, we show up when we say. Background-checked, uniformed technicians work on your property the way they’d work on their own mother’s driveway.
We’re trained and equipped on nine gate automation brands, so if your FAAC unit needs a part that’s backordered, we can often adapt a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing component without compromising the system. That multi-brand fluency means one visit, not three. And every job is covered by our 90-Day Done Right Promise. A gate should open when you want it to and stay closed when you don’t. Everything else is just keeping that promise.
FAQs
Yes. We install customer-supplied FAAC operators, though we’ll inspect the unit before mounting and tell you straight if it’s the wrong size or capacity for your gate. Installing an undersized operator on a heavy Tarzana driveway gate is a waste of your money and our time, and we won’t do it.
As an independent FAAC service provider, we’re not an authorized FAAC dealer, so manufacturer warranty terms depend on where you bought the unit and FAAC’s policies. We install to manufacturer specifications, use quality OEM or top-tier aftermarket parts, and stand behind the workmanship ourselves with our 90-Day Done Right Promise in writing. If a labor issue comes up, we handle it.
Most FAAC installations are completed one to two working days after the on-site assessment and parts order clear. Simple operator swaps can sometimes be done same week. If you have an existing FAAC unit that’s failed and you need a replacement mounted, call (925) 263-6107 and we’ll give you a realistic timeline, not a hopeful one.
If your FAAC unit is under ten years old and the failure is a control board, limit switch, or hydraulic seal, repair usually makes sense at $300-$800. If the unit is over fifteen years old, the hinge geometry is compromised, or the gearbox is grinding, replacement is the honest answer. We’ll tell you which one applies to your gate, and the assessment is free.
Yes. We pour gate-post footings, weld steel frames and hinges, and build to the weight and duty cycle your FAAC operator requires. A gate and its operator have to be engineered as one system. That’s what we do, start to finish, on every job in Tarzana.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Tarzana and nearby areas.