Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Parts & Welding in Tarzana: What to Know First
We provide independent FAAC gate parts and welding service across Tarzana, typically completing most hinge, weld, and roller repairs in a single visit with the part on the truck. An honest answer on cost: most FAAC gate parts and welding jobs in Tarzana fall between $285 and $950 depending on what actually failed, and we settle the price in writing before any work starts. This page is for FAAC owners in Tarzana whose gate has started sagging, dragging, or refusing to close square. If that sounds like your driveway, call (925) 263-6107 and a live person will answer, day or night.
How FAAC Products Fail - and How We Fix Them
FAAC builds solid operators, but the metal around them takes a beating in the San Fernando Valley. We see the same failures repeat across Tarzana driveways, and knowing the model line tells us where to look first.
- Swing gate hinge wear on FAAC 400 and 412 operators. The operator is rarely the first thing to fail. The hinge takes lateral load every time the wind pushes the gate leaf, and in Tarzana the Santa Ana season adds real stress. A worn hinge makes the FAAC motor work harder until it trips the thermal cutoff or strips the internal gear. We replace the hinge, true the leaf, and the motor stops fighting.
- Weld fatigue at the bottom rail on FAAC 391 and 770 gate leafs. Most residential gate leafs are hollow steel frames. Over years of heat and cold, the bottom rail weld cracks where it meets the hinge stile, especially on heavy ornamental leafs. The gate starts to twist when it opens. We grind out the failed weld, re-weld, and reinforce the joint so it does not crack again in the same place.
- Post movement causing FAAC limit switches to fall out of calibration. A leaning gate post changes the geometry the FAAC operator was set up for. The leaf closes too far or stops short, and the limit switches get blamed. In Tarzana’s expansive clay soil, posts shift seasonally. We reset the post in concrete, re-plumb it, and re-calibrate the limits the same day.
- Gate roller seizure on FAAC sliding gate systems, especially the 844 line. Rollers pack with dirt and lose their bearings, then the gate drags on the track and the FAAC motor draws high amps until the control board faults. We see this constantly on hillside properties off Reseda and Vanalden where dust blows in off the hills. New sealed rollers and a clean track bring the gate back to quiet operation.
- Latch and lock misalignment after years of gate sag. A gate that has dropped even a quarter inch no longer lines up with the latch post. Homeowners often shim or force it, which bends the latch and eventually the receiver. We weld the latch back into true position, shim the hinge side properly, and the gate latches like it should without a fight.
Our FAAC Gate Parts & Welding Process
Every FAAC job in Tarzana follows the same square-deal sequence. No shortcuts, no surprises.
- 1
Call and describe what the gate is doing. A live person answers. We ask about the model, the symptom, and whether the gate is stuck open, stuck closed, or moving wrong.
- 2
On-site inspection and honest diagnosis. Our technician examines the operator, the hinges, the welds, the rollers, and the post bases. We measure the gate’s clearances and watch it run. You get told straight what failed and what it will take to fix it.
- 3
Parts decision: OEM FAAC or quality aftermarket. For electrical components and control boards, we use OEM FAAC parts to keep the operator in spec. For structural steel, hinges, and rollers, we often use heavier aftermarket steel that outlasts the original. We explain the difference and let you choose with real numbers in front of you.
- 4
Written price before work begins. You get the number for parts and labor on paper, agreed to before we turn a single bolt or strike a single arc. If we find something hidden once we open it up, we stop and talk to you before doing anything else.
- 5
The repair or weld, done in one visit. Most FAAC gate parts and welding jobs in Tarzana are completed the same day. We grind, weld, true the leaf, replace the part, and re-calibrate the operator.
- 6
Full cycle test and cleanup. We open and close the gate a dozen times under load, check the limit settings, verify the safety edges, and clean up our work area. You get a written 90-Day Done Right Promise so if anything is not right, we come back and make it right.
What FAAC Gate Parts & Welding Costs in Tarzana
Here is what we charge for the common FAAC repairs we handle in Tarzana. These are real numbers for real scenarios, not bait pricing.
- Hinge replacement (single gate leaf): $285-$520 depending on hinge size and whether the post needs a weld plate
- Weld repair at rail or stile: $180-$400 per crack, including grinding and reinforcement
- Gate roller set (sliding FAAC gates): $240-$450 installed
- Post reset and re-plumb in concrete: $550-$950 including demolition, concrete, and re-hanging the leaf
- Latch and lock weld or alignment: $160-$340
- Full gate leaf fabrication with FAAC operator integration: $2,200-$6,000 depending on size, design, and steel weight
What moves the price: gate weight, steel thickness, whether we can work on the existing post or need to pour new footing, and whether the FAAC operator itself needs re-programming after the structural work. Every quote is written, free, and settled before work starts. Call (925) 263-6107 for an exact number on your gate.
Why Tarzana Homeowners Call Ironworks Gate Co. for FAAC Work
We have been fixing gates in the West Valley since 1984, and we have seen enough FAAC operators on Tarzana driveways to know their habits. Victor Salinas grew up off Reseda Boulevard and still works these same streets, so when we say we know how a FAAC 400 behaves on a hillside lot, we mean it from experience, not a manual. Every job, from a hinge replacement to a full gate build, carries our written 90-Day Done Right Promise. Our technicians are background-checked and uniformed, and they treat your driveway the way they would treat their own mother’s. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if the FAAC operator fails far from the hinges, we handle that too without calling in anyone else. A live person answers our phone 24 hours a day, every day. No voicemail tree, no callback queue, no waiting until Monday.
FAQs
If your FAAC operator is still under its original manufacturer warranty, we recommend OEM FAAC parts for anything electrical or operator-related, and honestly, that is what we use in those situations. For structural steel, hinges, and rollers, aftermarket parts do not affect the operator warranty because FAAC’s warranty covers the operator itself, not the gate hardware. As an independent FAAC service provider, we tell you plainly which parts make sense for your gate’s age and condition, and we never pretend to be authorized by the manufacturer. If your warranty matters to you, say so on the call and we will work within it. Call (925) 263-6107 and we will walk through your specific gate’s situation.
Most FAAC electronic parts are stocked on our service trucks or available from our local supplier within one business day, so a single-visit repair is the norm, not the exception. Structural steel, custom hinge plates, and unusual roller sizes may take a few days to fabricate if we need to cut and weld to your gate’s exact dimensions. Emergency calls for a gate stuck open or a fallen leaf are answered live 24/7. Call (925) 263-6107 and we will tell you the honest timeline for your exact FAAC model and the part it needs.
If the operator still runs and the gate leaf is structurally sound, repair is almost always the better money in Tarzana. We repair gates that have sagged, cracked, and dragged for years, and a good weld plus a fresh hinge usually costs a fraction of a new gate. Replacement makes sense when the steel is rusted through in multiple places, the post base is gone, or the gate was built too light for its size in the first place. We will tell you straight which side of that line your gate is on, and we will not sell you a new gate because it is an easier invoice. A gate should open when you want it to and stay closed when you don’t. Everything else is just keeping that promise.
We can weld most ornamental gate repairs and then touch up the affected area, but a perfect invisible repair on a powder-coated or painted finish is not always possible, and we will tell you that before we start. We grind the weld flush, prime the bare steel, and match the paint as close as the existing finish allows. On a gate from the 1980s or 1990s, the sun has already faded the original color, so a full respray of the repaired section is often the honest answer. If you want the gate to look untouched, we can refer you to a finisher we trust after the structural work is done.
We service both. Our technicians are trained on FAAC operators and the structural gate hardware around them, which matters because a FAAC 400 or 770 acts differently when the hinges and rollers are worn, and you cannot fix the operator’s behavior without fixing the metal first. We carry FAAC control boards, limit switches, capacitors, and receivers on the truck, and we re-program the operator after structural repairs so the whole system works as one. If your FAAC operator is flashing an error or the gate is moving wrong, call (925) 263-6107 and we will diagnose it the same day.
Need FAAC gate parts or welding in Tarzana? Call (925) 263-6107 for a free estimate and an honest answer about what your gate needs. A live person answers, 24 hours a day, 7 days a week.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Tarzana and nearby areas.